Altera Arria V Hard IP for PCI Express Instrukcja Użytkownika Strona 11
- Strona / 288
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Chapter 1: Datasheet 1–3
Features
December 2013 Altera Corporation Arria V Hard IP for PCI Express
User Guide
f The purpose of the Arria V Hard IP for PCI Express User Guide is to explain how to use
the Arria V Hard IP for PCI Express and not to explain the PCI Express protocol.
Although there is inevitable overlap between these two purposes, this document
should be used in conjunction with an understanding of the following PCI Express
specifications: PHY Interface for the PCI Express Architecture PCI Express 2.0 and PCI
Express Base Specification 2.1.
Transaction Layer Packet Types (TLP) (3)
■ Memory Read Request
■ Memory Read Request-Locked
■ Memory Write Request
■ I/O Read Request
■ I/O Write Request
■ Configuration Read Request
(Root Port)
■ Configuration Write Request
(Root Port)
■ Message Request
■ Message Request with Data
Payload
■ Completion without Data
■ Completion with data
■ Completion for Locked Read
without Data
■ Memory Read Request
■ Memory Write Request
■ Configuration Read Request
(Root Port)
■ Configuration Write Request
(Root Port)
■ Message Request
■ Message Request with Data
Payload
■ Completion without Data
■ Completion with Data
■ Memory Read Request (single
dword)
■ Memory Write Request (single
dword)
Maximum payload size 128–512 bytes 128–256 bytes
Number of tags supported for non-posted
requests
32 or 64 8
62.5 MHz clock Supported Supported
Multi-function
Supports up to 8 functions Supports single function only
Polarity inversion of PIPE interface signals Supported Supported
ECRC forwarding on RX and TX Supported Not supported
Expansion ROM Supported Not supported
Number of MSI requests 16 1, 2, 4, 8, or 16
MSI-X Supported Supported
Multiple MSI, MSI-X, and INTx Not Supported Supported
Legacy interrupts Supported Supported
Notes to Table 1–1:
(1) Not recommended for new designs.
(2) ×2 is supported by down training from ×4 or ×8 lanes.
(3) Refer to Appendix A, Transaction Layer Packet (TLP) Header Formats for the layout of TLP headers.
Table 1–2. Differences in Features Available Using the Avalon-MM and Avalon-ST Interfaces (Part 2 of 2)
Feature Avalon-ST Interface Avalon-MM Interface
- User Guide 1
- Contents 3
- Chapter 7. IP Core Interfaces 5
- Chapter 9. Reset and Clocks 5
- Chapter 18. Debugging 8
- 1. Datasheet 9
- 1–2 Chapter 1: Datasheet 10
- Features 10
- Notes to Table 1–1: 11
- Release Information 12
- Device Family Support 12
- Configurations 12
- Debug Features 13
- IP Core Verification 14
- Recommended Speed Grades 15
- 1–8 Chapter 1: Datasheet 16
- Qsys Design Flow 25
- Generating the Testbench 26
- Modifying the Example Design 34
- Running Qsys 36
- Table 3–5 38
- On Chip r 40
- Simulating the Example Design 44
- Direct BFM’s shared memory 47
- {*reconfig_xcvr_clk*} 50
- Compiling the Design 51
- Programming a Device 51
- System Settings 54
- Port Functions 55
- Error Reporting 57
- 31 19 18 17 16 15 14 58
- Power Management 59
- Legacy Interrupt 63
- Base Address Registers 66
- PCI Express/PCI Capabilities 67
- Header 68
- 6. IP Core Architecture 75
- Avalon-ST Interface 77
- RX Datapath 77
- TX Datapath 77
- Altera FPGA 77
- Clocks and Reset 78
- Interrupts 79
- Transaction Layer 79
- Protocol Layers 80
- Configuration Space 81
- Data Link Layer 81
- Figure 6–4. Data Link Layer 82
- Physical Layer 83
- Figure 6–5. Physical Layer 84
- Multi-Function Support 86
- PCI Express Avalon-MM Bridge 86
- Avalon-MM Bridge TLPs 88
- Figure 6–9. Poor Address Map 93
- RX Block 97
- Avalon-MM RX Master Block 97
- TX Block 98
- Interrupt Handler Block 98
- 7. IP Core Interfaces 99
- Note to Table 7–1: 100
- RX Port 101
- Avalon-ST RX Interface 103
- Note to Figure 7–7: 108
- Avalon-ST TX Interface 113
- Note to Table 7–4: 116
- ECRC Forwarding 121
- Clock Signals 121
- Reset Signals 122
- and the LTSSM L0 state 124
- ECC Error Signals 125
- Interrupts for Endpoints 125
- Interrupts for Root Ports 126
- Completion Side Band Signals 126
- Specification, Rev. 2.1 128
- D E F 0 1 2 3 131
- Notes to Table 7–13: 132
- LMI Signals 136
- LMI Read Operation 137
- LMI Write Operation 137
- Power Management Signals 138
- (Full-Featured Qsys) 140
- Completer-Only Single DWord 141
- RX Avalon-MM Master Signals 143
- Transceiver Reconfiguration 145
- Serial Interface Signals 145
- PIPE Interface Signals 149
- Test Signals 153
- Notes to Table 7–27: 154
- 8. Register Descriptions 155
- Note to Table 8–2: 156
- Note to Table 8–3: 157
- Note to Table 8–4: 157
- Note to Table 8–5: 157
- Note to Table 8–6: 158
- Note to Table 8–7: 158
- Note to Table 8–8: 159
- PCI Express Mailbox Registers 167
- Note to Table 8–30: 168
- Root Port TLP Data Registers 170
- Sending a TLP 173
- Receiving a Completion TLP 173
- Endpoints 174
- Avalon-MM Mailbox Registers 175
- Spec 2.1 176
- 9. Reset and Clocks 181
- Example Design 182
- Hard IP for PCI Express 182
- 127 cycles 184
- ±300 PPM 185
- Note to Table 9–2: 186
- Transceiver Clock Signals 187
- Supported Message Types 189
- Notes to Table 10–1: 191
- Receive Buffer Reordering 192
- Notes to Table 10–2: 193
- MSI Interrupts 195
- 11–2 Chapter 11: Interrupts 196
- Note to Figure 11–4: 197
- Legacy Interrupts 198
- Application Layer 199
- 11–6 Chapter 11: Interrupts 200
- MSI/MSI-X Support 201
- Qsys System 202
- 12. Optional Features 203
- ECRC on the RX Path 204
- ECRC on the TX Path 205
- 13. Flow Control 207
- 13–2 Chapter 13: Flow Control 208
- Throughput of Posted Writes 208
- Chapter 13: Flow Control 13–3 209
- 13–4 Chapter 13: Flow Control 210
- 14. Error Handling 211
- Physical Layer Errors 212
- Data Link Layer Errors 212
- Transaction Layer Errors 213
- Note to Table 14–4: 215
- Figure 15–2 218
- Core User Guide 219
- 16. SDC Timing Constraints 221
- Endpoint Testbench 224
- Root Port Testbench 225
- Chaining DMA Design Examples 226
- Root Complex 227
- Chaining DMA 227
- Hard IP for 227
- PCI Express 227
- Note to Table 17–2: 232
- Note to Table 17–4: 233
- Test Driver Module 236
- DMA Write Cycles 237
- DMA Read Cycles 239
- Root Port Design Example 240
- Root Port 241
- Variation 241
- (variation_name.v) 241
- Root Port BFM 242
- BFM Memory Map 244
- Figure 17–6 248
- BFM Read and Write Procedures 250
- BFM Procedures and Functions 251
- BFM Configuration Procedures 256
- Shared Memory Constants 257
- 18. Debugging 271
- 18–2 Chapter 18: Debugging 272
- Link Training 272
- Chapter 18: Debugging 18–3 273
- 18–4 Chapter 18: Debugging 274
- Chapter 18: Debugging 18–5 275
- Setting Up Simulation 276
- Chapter 18: Debugging 18–7 277
- Use Third-Party PCIe Analyzer 278
- BIOS Enumeration Issues 278
- Notes to Table A–7: 280
- Chapter : A–3 281
- Notes to Table A–16: 282
- Additional Information 283
- Info–2 Revision History 284
- How to Contact Altera 285
- Typographic Conventions 286
Powiązane produkty i podręczniki dla Urządzenia pomiarowe Altera Arria V Hard IP for PCI Express
(286 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.232 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji