Altera Triple Speed Ethernet MegaCore Function Instrukcja Użytkownika Strona 199
- Strona / 223
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
DefaultDescriptionParameter
10: Disables padding.
1: If the length of frames generated by the GMII/RGMII/MII Ethernet
frame generator is less than the minimum frame length (64 bytes), the
generator inserts padding bytes to the frames to make up the minimum
length.
TB_ENA_PADDING
00: Only basic frames are generated.
1: Enables VLAN frames generation. This value specifies the number
of basic frames generated before a VLAN frame is generated followed
by a stacked VLAN frame.
TB_ENA_VLAN
0Specifies the number of packets to be read from the receive FIFO before
reading is suspended. You can use this parameter to test FIFO overflow
and flow control.
TB_STOPREAD
1000Specifies the number of clock cycles before the Avalon-ST monitor
stops reading from the receive FIFO.
TB_HOLDREAD
00: Normal behavior.
1: Drives the Avalon-ST error signal high to simulate erroneous frames
transmission.
TB_TX_FF_ERR
0Specifies the number of clock cycles from the start of simulation before
the xoff_gen signal is driven.
TB_TRIGGERXOFF
0Specifies the number of clock cycles from the start of simulation before
the xon_gen signal is driven high.
TB_TRIGGERXON
0Specifies which frame is received with collision. Valid in fast Ethernet
and half-duplex mode only.
RX_COL_FRM
0Specifies which nibble within the frame collision occurs.RX_COL_GEN
0Specifies which frame is transmitted with a collision. Valid in fast
Ethernet and half-duplex mode only.
TX_COL_FRM
0Specifies which nibble within the frame collision occurs on the transmit
path.
TX_COL_GEN
0Specifies the number of consecutive collisions during retransmission.TX_COL_NUM
0Specifies the delay, in nibbles, between collision and retransmission.TX_COL_DELAY
10: GMII frame generator does not respond to pause frames.
1: Enables flow control in the GMII frame generator.
TB_PAUSECONTROL
0Enable / Disable MDIO simulation.TB_MDIO_SIMULATION
Supported in configurations that contain the 1000BASE-X/SGMII PCS
00: Disables half-duplex mode.
1: Enables half-duplex mode.
TB_SGMII_HD
Simulation Parameters
Altera Corporation
Send Feedback
UG-01008
Test Configuration Parameters
B-4
2014.06.30
- User Guide 1
- Contents 2
- Altera Corporation 10
- About This MegaCore Function 10
- Send Feedback 10
- High-Level Block Diagrams 10
- Figure 1-2: Multi-port MAC 11
- 10/100/1000-Mbps 12
- Ethernet MAC 12
- Optical Platform 14
- Copper Platform 14
- Release Information 18
- DescriptionItem 19
- Using the Parameter Editor 24
- Design Walkthrough 25
- Simulate the System 27
- Programming an FPGA Device 27
- Generated Files 28
- DescriptionFile Name 29
- Quartus II Pin 29
- Assignment 29
- Parameter Settings 30
- Ethernet MAC Options 31
- FIFO Options 33
- Timestamp Options 34
- PCS/Transceiver Options 34
- ParameterValueName 35
- Functional Description 37
- MAC Architecture 38
- MAC Interfaces 39
- MAC Transmit Datapath 40
- IP Payload Re-alignment 41
- Address Insertion 41
- Frame Payload Padding 41
- CRC-32 Generation 41
- Interpacket Gap Insertion 42
- MAC Receive Datapath 43
- ValueHash Code Bit 44
- Frame Type Validation 45
- Payload Pad Removal 46
- CRC Checking 46
- Length Checking 46
- Frame Writing 47
- IP Payload Alignment 47
- FIFO Buffer Thresholds 48
- Receive Thresholds 49
- Transmit Thresholds 51
- Congestion and Flow Control 52
- Magic Packets 53
- MAC Local Loopback 54
- MAC Error Correction Code 55
- MAC Reset 55
- PHY Management (MDIO) 56
- MDIO Connection 57
- MDIO Frame Format 57
- Gigabit Ethernet 58
- Programmable 10/100 Ethernet 59
- Transmit Operation 62
- Receive Operation 63
- SGMII Converter 64
- Auto-Negotiation 65
- SGMII Auto-Negotiation 66
- Ten-bit Interface 68
- PHY Loopback 69
- PHY Power-Down 69
- POWERDOWN 70
- 1000BASE-X PCS 70
- IEEE 1588v2 Features 72
- Time of Day 73
- IEEE 1588v2 Receive Datapath 74
- IEEE 1588v2 Frame Format 74
- 0..1500/9600 Octets 75
- 4 Octets 75
- CRC4 Octets 76
- 0..1500/9600 Octets Payload 76
- MAC Header 77
- UDP Header 77
- IP Header 77
- PTP Header 77
- Software Requirements 78
- Base Addresses 80
- IEEE 1588v2 Feature PMA Delay 100
- UG-01008 101
- 2014.06.30 101
- DescriptionR/WNameBit(s) 103
- DescriptionR/WNameBit 105
- 1000BASE-X 106
- Register Initialization 110
- Configuration Register Space 111
- Interface Signals 116
- Clock and Reset Signal 117
- MAC Control Interface Signals 118
- MAC Status Signals 118
- MAC Receive Interface Signals 119
- DescriptionBit 120
- DescriptionI/OName 123
- MII/GMII/RGMII Signals 124
- PHY Management Signals 125
- ECC Status Signals 126
- TBI Interface Signals 131
- Status LED Control Signals 132
- SERDES Control Signals 132
- Related Information 133
- SectionInterface Signal 135
- 1.25 Gbps Serial Interface 138
- Transceiver Native PHY Signal 138
- DescriptionWidthI/OSignal 141
- 1000BASE-X/SGMII PCS Signals 149
- PCS Control Interface Signals 150
- PCS Reset Signals 150
- SGMII Status Signals 152
- Avalon-ST Receive Interface 155
- IEEE 1588v2 Timestamp 162
- Design Considerations 163
- Configurations(1) 164
- Sharing Transceiver Quads 169
- Timing Constraints 171
- Recommended Clock Frequency 173
- 50–100CLK 174
- 1000BASE-X/SGMII PCS only 174
- 125REF_CLK 174
- 125TBI_TX_CLK 174
- 125TBI_RX_CLK 174
- Testbench 175
- Testbench Verification 176
- Testbench Configuration 177
- Test Flow 177
- Simulation Model 178
- Simulation Model Files 179
- Driver Architecture 180
- PHY Speed Bits 181
- Speed (Mbps) 181
- Using Jumbo Frames 183
- API Functions 184
- Constants 189
- DescriptionValueConstant 190
- Ethernet Frame Format 192
- Pause Frame Format 194
- Description 195
- XON_GENXOFF_GEN 195
- Simulation Parameters 196
- DefaultDescriptionParameter 197
- Test Configuration Parameters 198
- Time-of-Day (ToD) Clock 201
- ToD Clock Parameter Setting 202
- ToD Clock 203
- DescriptionR/WNameDword 205
- Adjusting ToD Clock Drift 206
- ToD Synchronizer 207
- ToD Synchronizer Block 208
- 32/6364/31516/6364/63Settings 209
- DescriptionValueName 209
- ToD Synchronizer Signals 210
- Packet Classifier 212
- Packet Classifier Signals 213
- Additional Information 217
- Document Revision History 218
- ChangesVersionDate 219
- How to Contact Altera 223
Powiązane produkty i podręczniki dla Urządzenia pomiarowe Altera Triple Speed Ethernet MegaCore Function
Urządzenia pomiarowe Altera 8B10B Encoder/Decoder MegaCore Function Instrukcja Użytkownika
(32 strony)
(32 strony)
Urządzenia pomiarowe Altera I/O Phase-Locked Loop (Altera IOPLL) IP Core Instrukcja Użytkownika
(11 strony)
(11 strony)
Urządzenia pomiarowe Altera Embedded Systems Development Kit, Cyclone III Edit Instrukcja Użytkownika
(82 strony)
(82 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji