Altera Embedded Peripherals IP Instrukcja Użytkownika Strona 109
- Strona / 336
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
from 8 to 32. After a master peripheral writes a value to the txdata register, the value is copied to the shift
register and then transmitted when the next operation starts.
The shift register and the txdata register provide double buffering during data transmission. A new value
can be written into the txdata register while the previous data is being shifted out of the shift register.
The transmitter logic automatically transfers the txdata register to the shift register whenever a serial
shift operation is not currently in process.
In master mode, the transmit shift register directly feeds the mosi output. In slave mode, the transmit shift
register directly feeds the miso output. Data shifts out LSB first or MSB first, depending on the configura‐
tion of the SPI core.
Receiver Logic
The SPI core receive logic consists of a receive holding register (rxdata) and receive shift register, each n
bits wide. The register width n is specified at system generation time, and can be any integer value from 8
to 32. A master peripheral reads received data from the rxdata register after the shift register has captured
a full n-bit value of data.
The shift register and the rxdata register provide double buffering while receiving data. The rxdata
register can hold a previously received data value while subsequent new data is shifting into the shift
register. The receiver logic automatically transfers the shift register content to the rxdata register when a
serial shift operation completes.
In master mode, the shift register is fed directly by the miso input. In slave mode, the shift register is fed
directly by the mosi input. The receiver logic expects input data to arrive LSB first or MSB first, depending
on the configuration of the SPI core.
Master and Slave Modes
At system generation time, the designer configures the SPI core in either master mode or slave mode. The
mode cannot be switched at runtime.
Master and Slave Modes
In master mode, the SPI ports behave as shown in the table below.
Table 10-1: Master Mode Port Configurations
Name Direction Description
mosi output Data output to slave(s)
miso input Data input from slave(s)
sclk output Synchronization clock to all slaves
ss_
nM
output Slave select signal to slave M, where M is a number
between 0 and 31.
In master mode, an intelligent host (for example, a microprocessor) configures the SPI core using the
control and slaveselect registers, and then writes data to the txdata buffer to initiate a transaction. A
master peripheral can monitor the status of the transaction by reading the status register. A master
peripheral can enable interrupts to notify the host whenever new data is received (for example, a transfer
has completed), or whenever the transmit buffer is ready for new data.
The SPI protocol is full duplex, so every transaction both sends and receives data at the same time. The
master transmits a new data bit on the mosi output and the slave drives a new data bit on the miso input
UG-01085
2014.24.07
Receiver Logic
10-3
SPI Core
Altera Corporation
Send Feedback
- 101 Innovation Drive 1
- San Jose, CA 95134 1
- Contents 2
- Altera Corporation 10
- Introduction 14
- Device Support 15
- December 16
- Initial release. — 16
- SDRAM Controller Core 17
- Avalon-MM Interface 18
- Off-Chip SDRAM Interface 18
- Memory Profile Page 21
- Timing Page 22
- SDRAM Memory Model 23
- Symptoms of an Untuned PLL 26
- Example Calculation 27
- Parameter Symbol 28
- Value (ns) in -7 Speed Grade 28
- Min. Max 28
- Parameter Symbol Value (ns) 28
- Tri-State SDRAM 31
- Configuration Parameter 32
- Interface 33
- Reset and Clock Requirements 38
- Architecture 38
- Block Level Usage Model 39
- Compact Flash Core 41
- Required Connections 42
- (32-bit Word Address) 54
- Register Name R/W 54
- Bit Description 54
- JTAG UART Core 58
- Read and Write FIFOs 59
- JTAG Interface 59
- Host-Target Connection 59
- Simulation Settings 61
- UART Core 70
- RS-232 Interface 71
- Transmitter Logic 71
- Instantiating the Core 72
- Data Bits, Stop Bits, Parity 73
- Synchronizer Stages 74
- Flow Control 74
- Streaming Data (DMA) Control 74
- Request Description 79
- Bit Name Access Description 81
- May 2008 86
- 16550 UART 87
- Unsupported Features 88
- General Architecture 90
- Configuration Parameters 90
- DMA Support 91
- FPGA Resource Usage 91
- Timing and Fmax 92
- Avalon-MM Slave 93
- Overrun/Underrun Conditions 94
- Hardware Auto Flow-Control 95
- 16550 UART API 98
- Private APIs 99
- UART Device Structure 100
- Figure 9-7: 101
- Driver Examples 102
- UG-01085 103
- 2014.24.07 103
- Document Revision History 106
- SPI Core 107
- txdata 108
- Receiver Logic 109
- Master and Slave Modes 109
- Slave Mode Operation 110
- Multi-Slave Environments 110
- Configuration 111
- Data Register Settings 112
- Timing Settings 112
- Software Programming Model 113
- Software Files 114
- Register Map 115
- # Name Description 116
- Date and 118
- Document 118
- Core Overview 119
- Functional Description 119
- Interrupt Behavior 121
- PIO Core 123
- Data Input and Output 124
- Edge Capture 124
- IRQ Generation 124
- Example Configurations 125
- Input Options 126
- Operation 132
- PCI Lite Core 135
- Avalon-MM Ports 137
- Prefetchable Avalon-MM Master 137
- I/O Avalon-MM Master 138
- PCI Bus Access Slave 138
- Master and Target Performance 139
- Space Indicator 141
- (Bits 1:0) 141
- Description 141
- Avalon-to-PCI Write Request 142
- Ordering of Requests 143
- Send Feedback 145
- PCI Timing Constraint Files 146
- Simulation Considerations 147
- Simulation Flow 149
- MDIO Core 151
- MDIO Frame Format (Clause 45) 152
- MDIO Clock Generation 153
- Interfaces 153
- Parameter 154
- Configuration Registers 154
- On-Chip FIFO Memory Core 156
- Offset Bits Field Description 158
- FIFO Settings 161
- Interface Parameters 161
- Software Control 163
- Field Type Description 164
- Bit(s) Name Description 164
- Software Example 166
- On-Chip FIFO Memory API 167
- Multi-Channel Shared FIFO 176
- Parameters 177
- Address Width 178
- Name Access Reset 180
- Bytes Converter Cores 185
- Feature Property 186
- Transaction 190
- DMA Descriptors 197
- Error Conditions 198
- Signal Type Description 199
- Timeouts 206
- Data Structure 207
- SG-DMA API 208
- Name Description 209
- Overview 217
- Feature Description 217
- Component Interface 220
- Descriptor Slave Port 221
- Component GUI 222
- Byte Lanes 223
- Read and Write Address Fields 224
- Length Field 224
- Sequence Number Field 225
- Read and Write Stride Fields 225
- Control Field 225
- Bit Sub-Field Name Definition 226
- Register Map of mSGDMA 228
- Status Register 229
- Control Register 229
- Bit Name Description 230
- Offset Access 3 2 1 0 230
- Unsupported Feature 231
- DMA Controller Core 232
- Setting Up DMA Transactions 233
- Advanced Options 235
- Video Sync Generator 242
- Parameter Name Description 244
- Horizontal sync pulse 245
- Horizontal front porch 245
- Horizontal blank pixels 245
- Pixel Converter 246
- Interval Timer Core 249
- Counter Size 251
- Hardware Options 251
- Bit Name R/W/C Description 255
- Mutex Core 258
- Mutex API 260
- Mailbox Core 264
- Mailbox API 267
- Functional Blocks 273
- Register Maps 275
- Run-time Initialization 285
- Board Support Package 285
- VIC IRQ RRS RIL 291
- November 293
- Altera FPGA 294
- Core Behavior 295
- System ID Core 298
- Performance Counter Core 301
- Global Counter 302
- Using the Performance Counter 304
- Name (1) Meaning 305
- Performance Counter API 306
- PERF_START_MEASURING() 307
- PERF_STOP_MEASURING() 307
- PERF_BEGIN() 307
- PERF_END() 308
- PLL Cores 312
- Registers 313
- PLL Core 313
- ALTPLL Megafunction 313
- Instantiating the PLL Core 314
- Altera MSI to GIC Generator 320
- Interrupt Servicing Process 321
- Registers of Component 322
- Altera SMBus Core Interface 324
- Component Parameterization 326
- Frequency Register 331
- 32-bit Counter 332
- Software Access 334
- Implementation Details 335
- IP Caveats 336
Powiązane produkty i podręczniki dla Urządzenia pomiarowe Altera Embedded Peripherals IP
Urządzenia pomiarowe Altera Nios II Embedded Evaluation Kit Cyclone III Editio Instrukcja Użytkownika
(80 strony)
(80 strony)
Urządzenia pomiarowe Altera Phase-Locked Loop Reconfiguration IP Core Instrukcja Użytkownika
(51 strony)
(51 strony)
Urządzenia pomiarowe Altera Serial Digital Interface (SDI) MegaCore Function Instrukcja Użytkownika
(140 strony)
(140 strony)
Urządzenia pomiarowe Altera 100G Development Kit, Stratix V GX Edition Instrukcja Użytkownika
(44 strony)
(44 strony)
Urządzenia pomiarowe Altera Stratix V Avalon-MM Interface for PCIe Solutions Instrukcja Użytkownika
(184 strony)
(184 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji